Bitwar Android 檔案救援下載
  •   Root Phone with PC
    How to Root an Android Phone (With PC)

    .Summary: This article lays out the most common way for users to root an Android phone on a PC. Prerequisites Make sure you have met the following requirements: Device powered ON At least 50% battery level Internet connection necessary USB Cable (the original one recommended) The Complete Guide to Root an Android Phone Step 1: Download and install KingoRoot Android (PC version). Step 2: Launch the software, and you will see the primary interface. Step 3: Connect your phone to the computer with a USB cable. Note: If the corresponding device driver hasn't been installed on the computer, the software will automatically download and install it. Make sure the internet connection works appropriately; otherwise, the software can't download the driver. Step 4: Enable USB debugging mode on your phone A prompt will pop up on your device; please tap "Always allow from this computer" Note: Users who don't know how to enable USB debugging mode can refer to the following guide: Step 5: Click on ROOT to root. The process should take a couple of minutes. During the rooting, it's ordinary that the device may automatically reboot several times, and users should not perform any operation on the device. Step...

    2020-8-1

  •   Root Phone without PC
    如何生根 Android 手機(無 PC)

    摘要:本文列出了用戶在不連接 PC 的情況下對您的 Android 手機進行 root 的最常見方法。先決條件 確保您已滿足以下先決條件: 設備已開機。至少 50% 的電池電量。需要互聯網連接(建議使用 Wi-Fi 網絡)。允許安裝來自未知來源的應用程序。 (一般路徑:設置 > 安全 > 未知來源) Android 手機完全指南(無 PC) 第 1 步:下載 KingoRoot Android (APK) 並將其傳輸到您的 Android 設備。然後,通過文件資源管理器找到該文件並安裝它。您也可以在手機上訪問該網站進行下載和安裝。第二步:開始安裝軟件。如果您尚未授予未知來源的應用程序安裝權限,則會彈出警告對話框:“為安全起見,您的手機已設置為阻止安裝來自未知來源的應用程序。”執行後面的對話顯示的內容以授予權限。步驟3:啟動軟件並點擊“一鍵Root”開始生根。步驟4:等待生根結果。有可能生根失敗。別著急,重新開始。通常,它不會花太長時間...

    2020-8-1

  •   Install Backup Tool
    如何安裝鏡像工具來備份您的 Android 手機

    摘要:本文描述了在 Bitwar Android Data Recovery 識別手機後如何在您的 android 手機上安裝鏡像工具。鏡像工具是用戶在嘗試從 Android 手機恢復丟失文件之前應安裝的一項要求。使用以下步驟了解如何安裝它。第一步:軟件識別出你的安卓手機後,會自動下載鏡像工具到手機上。請注意,有時手機屏幕上可能會彈出一個對話框,要求用戶決定是否安裝。請點擊安裝。注意:如果手機沒有提示安裝,請參考安裝失敗怎麼辦?該部分寫在本文的底部。第二步:啟動鏡像工具,點擊安裝。請注意,手機可能會彈出一個提示,要求用戶授予 root 權限。如果是這樣,請單擊同意。第三步:等待手機提示安裝完成。安裝失敗怎麼辦?如果手機沒有要求安裝或安裝過程結束時安裝失敗,第一個解決方案是關機...

    2020-8-1

  •   Connect Android Device
    如何將您的 Android 設備連接到您的計算機?

    摘要:本文向用戶解釋瞭如何將您的 android 設備連接到您的計算機以使用 Bitwar Android Data Recovery。確保您的設備已植根該軟件將自動檢測您的 android 設備是否已植根。如果設備尚未root,請單擊鏈接以了解如何為您的設備root:如何為Android 手機(帶PC)紮根如何為Android 手機(不帶PC)在設備上啟用USB 調試開啟USB調試模式,軟件會自動檢測。如果沒有,軟件會顯示如下圖: 並且由於不同的Android手機可能有不同的Android版本,因此開啟USB調試的方式也不同。點擊鏈接了解如何啟用USB調試:如何在Android設備上啟用USB調試 順便說一句,用戶無需擔心USB驅動程序,因為軟件檢測到您的設備後,它會自動下載相應的USB 驅動程序。手機root並開啟USB調試模式後,用戶應該可以將設備連接到電腦,軟件會顯示主界面:

    2020-8-1

  •   Solve Re-Backup Problems
    使用Bitwar Android數據恢復時如何解決重新備份問題

    總結:本文向用戶解釋了何時會出現重新備份問題以及如何解決這些問題。軟件會在三種情況下要求重新備份。情況 1:不同的 Android 設備 當 PC 當前具有以前的 Android 設備的備份文件時,會發生這種情況。用戶如果想恢復當前設備上的數據,需要備份當前設備。如果用戶想從PC上存儲的備份中恢復文件,點擊軟件右上角註冊旁邊的更多菜單,選擇LoadMirror加載備份。情況 2:不完整的備份文件 這種情況發生在上次備份過程中出現中斷時。備份過程停止、設備與PC斷開連接或備份過程中退出程序等操作都可能導致重新備份請求,如下圖所示。您可以單擊取消使軟件掃描不完整的備份文件。幸運的話,您可以恢復想要的文件。如果失敗,則返回同一階段,這次單擊“確定”進行完整的重新備份。情況 3:過時的備份文件...

    2020-8-1